My 94 GT Vert Build

[cwh19]

I've retyped this many times and it got lame ha. So I'm just going to post a ton of pictures and say where I'm at now.

The plans are as follows:

Performance:
1. Ported cobra intake
2. Ported Gt40s
3. Fox throttle conversion
4. Mac Longtubes
5. Offroad H pipe
6. 75mm throttle body
7. FMIC for the S-trim
8. Blow thru mass air with tial BOV

Other mechanical:
1. Transgo manual valvebody
2. Flaming River manual steering conversion
3. Battery relocation to trunk
4. New headlights
5. New taillights

Cleanup:
1. Redo the inside of the trunk
2. Redo the underside of the car
3. Rear seat delete


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0056.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0063.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0065.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0066.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0070.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0069.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0079.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0077.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0078.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0076.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0057.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0058.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0064.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0067.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0068.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0071.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0073.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0086.jpg

[Rodeheavers]

that trunk looks 100% better!

[cwh19]

The manual steering has been installed and I'm slowing collecting parts. I have the headers, midpipe, valvebody, and the heads and intake are at Rodeheavers getting cleaned up and ported.

The plan is to have it done by the middle of march to have a dyno tune from Don Lasota.

[cwh19]

that trunk looks 100% better!

Thanks man. It was pretty rough. There were some small rust holes that i dremel'd out. I need to patch those and give it some paint still.

[cwh19]

Ordered an 80mm bkk throttle body thats on the way. All the major parts for the top end i have now.

[casper gt]

ahh, white mustangs................. oh yeah, looks good so far.

[2001GTTT]

looks real good colton......let me know if you need a hand.

[cwh19]

ahh, white mustangs................. oh yeah, looks good so far.

Thanks man.

looks real good colton......let me know if you need a hand.

Once I get the heads and intake back from Tim, Chris and maybe keith are going to be coming out to set the rockers and such. I'm sure you could probably come when that goes down.

[cwh19]

Ordered some more good stuff today ;) . I almost have everything to put my junk back together.

I'll take pictures of everything once the stuff gets delivered.

[cwh19]

Ordered the final peice of the puzzle. Artsparts on corral is the man. Jdsperformance now but still, hes the man.

Now all I need is some misc gaskets and lots of time haha. :thumb:

[cwh19]

Got a new shiny part today.



http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0129.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0128.jpg





A 3" Pmass Protube and a 31x12x3 Intercooler are in the mail.

[cwh19]

Intercooler and piping kit!


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0134.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0133.jpg

[police4.6]

wait is that ALL of the piping????

[cwh19]

wait is that ALL of the piping????

Yes sir. well and the MAF which is in pipe form. It'll be enough.

[2001GTTT]

those are some nice pieces colton, cant wait till spring.

[police4.6]

Yes sir. well and the MAF which is in pipe form. It'll be enough.

wait i thought you had to get the stuff bent by someone else???? if so then i cant wait til we get those heads back from tim.. lol we might have to take a week off from school and work :eyebrows:

[cwh19]

those are some nice pieces colton, cant wait till spring.

Ha i know. I can't wait to put it back together.

wait i thought you had to get the stuff bent by someone else???? if so then i cant wait til we get those heads back from tim.. lol we might have to take a week off from school and work :eyebrows:

I decided to just go with a piping kit. I've read about people using them and they seem like good quality. Everything I need except for head gaskets have been purchased so its close.

[cwh19]

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0136.jpg


The new blow through mass air meter. I also got in my SLP LM1s today. Just need to get the heads and intake back from Tim and I'm ready to put it back together. :hungry:

[police4.6]

lets get that stuff put on... seriously how soon you getting the heads? i wanna get this thing tuned first of march

[2001GTTT]

lets get that stuff put on... seriously how soon you getting the heads? i wanna get this thing tuned first of march

hey paul revere, dont u have british to kill?

[cwh19]

lets get that stuff put on... seriously how soon you getting the heads? i wanna get this thing tuned first of march

I get the heads when Tim is done ha. So whenever that is, although I think it'll be soon. I told him before that there isn't a big rush.

[cwh19]

Sweet valentines day gifts. Head studs and valve cover breathers. :biggrin1:

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0145.jpg

[2001GTTT]

Ka-boom

[cwh19]

My goal is 425 at the wheels. Tons of stock blocks have lived at that for years. Its safe. I don't understand why you guys don't understand this lol.

[94svtcobra]

colton's engine's theme song

YouTube- Saliva - Click Click Boom

[police4.6]

colton it has nothing to do with they dont understand it they are just jealous

[94svtcobra]

my car will beat his in a race and in sex appeal

[scott5]

My goal is 425 at the wheels. Tons of stock blocks have lived at that for years. Its safe. I don't understand why you guys don't understand this lol.

You will be ok.. If you do the math ( i think you have a 5spd)
425 x 15% = 63.75
425 + 63.75 = 488.75
If auto just take the 15% out and put in 20%, but auto is alot more involved like stall and other such things but those seem to be the medium numbers also.

Now you are knocking on the limits doors. You are close to that 500hp mark.. Some have blown up with less and some have taken it way past that but 500hp seems to be the medium everyone takes into consideration.. Now take that and add the boost that you will be throwing onto and the occaisonal street race/track use/show off alil and you get pretty close to the limits, But you should be fine for a while as long as you dont miss too many gears when your on it:bounce: lol

But while i say that my buddy has a 349 B50(only a few more hp better than stock) block foxbody that put down 505rwhp at Rodeheavers Dyno day untuned with an s-trim and ran a 10.65 @13x cant remember the exact mph and his is still going strong.. So its basically down to luck. lol

[94svtcobra]

auto son

[scott5]

if its an auto in that case it will go ka boom cause of the wuss factor

[cwh19]

if its an auto in that case it will go ka boom cause of the wuss factor

Yea the auto is the worst part for sure. I bought a full manual valvebody from clark though so that'll make it a little more fun. Whenever a new tranny is needed, it'll be a TKO 600.

[cwh19]

We got the bumper cover off today and removed some stuff to make room for the sexy new intercooler.



http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0146.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0147.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0148.jpg

[scott5]

Yea the auto is the worst part for sure. I bought a full manual valvebody from clark though so that'll make it a little more fun. Whenever a new tranny is needed, it'll be a TKO 600.

If your just going to cruise it why not get a viper spec t-56?

[2001GTTT]

if its an auto in that case it will go ka boom cause of the wuss factor

anytime you wanna go scotty, oh wait, you dont have a car that runs. :third:

[scott5]

anytime you wanna go scotty, oh wait, you dont have a car that runs. :third:

i got a bike that has less cylinders, so anytime your feeling froggy or we can both race off road since we both have the same ground clearance:fish2:

[2001GTTT]

typical ricer.....I thought u knew better scott-tro

[scott5]

typical ricer.....I thought u knew better scott-tro

so you would have no problem racing it?

[MBH]

we can both race off road since we both have the same ground clearance:fish2:

hahahahahahahahahhahaahah


ohhhhh clark he got you bad

[cwh19]

If your just going to cruise it why not get a viper spec t-56?

Plans might change. We shall see.

[cwh19]

Got the heads and intake back from Tim today and they look great! I'll take some pictures tomorrow. Let the reassembly begin. :peace:

[cwh19]

Jacked up the motor to drop the headers down in and also installed one of the heads yesterday. Ran into a little snag with the other head but it should be on tomorrow. Then comes the awesome job of setting rockers. That should be a treat. We also mocked it up some just to get an idea of how high its going to sit.


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0150.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0151.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0149.jpg

[cwh19]

Got the other head and headers installed. Its soo close. I can't wait to get it running again.


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0154.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0156.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0155.jpg

[94svtcobra]

cant wait for it to :boom:

[police4.6]

you know mike i would have to say you are jealous

[94svtcobra]

of wat? I'm goin to beat him on the way to carisle

[cwh19]

of wat? I'm goin to beat him on the way to carisle

Lol you know I really dont care right? I'm just looking to have the nicest car that I can build. Thats it.

[94svtcobra]

u may not but I do

[police4.6]

hahaha mike i bet you a thousand dollars i will beat you to the carlisle exit and i will drive the speed limit

[2001GTTT]

i will beat you both. so f off.

[police4.6]

clark are you on the toilet and on here too? didnt you just tell me you had to number 2?

[2001GTTT]

lol negative im on my bed son

however, it could be done, seeing as this is my laptop...not a bad idea caleb, not a bad idea.

[police4.6]

i could be warm and poop at the same time??? and on my laptop?? here is a blank check.. write whatever amount you want to. < family guy reference minus the laptop

[94svtcobra]

I cant wait to see coltons face when I beat him

[cwh19]

Got lots more done over yesterday and today. Got the rockers, valve covers, and lower intake all on. I hope to have it all put back together by the end of next week. Unfortunately i wont be able to start it yet. i have to send my BOV to tial and have them change out the spring. it came with an 11 and I need a 3. I just hope it only takes a week or so to do the switch.






http://i938.photobucket.com/albums/ad230/cwh19/Project/002.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/003.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/006.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/007.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/010.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/011.jpg

[police4.6]

disgusting mike doesnt stand a chance.

[94svtcobra]

we'll see, we'll see

[2001GTTT]

disgusting mike doesnt stand a chance.



:wacko:

[scott5]

looking good man.. keep up the good work.. coming along nicely.. me and my buddy will hopefully start putting the 6.0 together in the camaro and get it ready for the 35psi it will be seeing from the good ole Vortech YSI...


can i get in of some of that fun when you guys race?

[scott5]

what size rr you use?

[police4.6]

what size rr you use?

magnum

[Pop's Stang]

Did you find that wrench you were looking for?:biggrin:

[cwh19]

looking good man.. keep up the good work.. coming along nicely.. me and my buddy will hopefully start putting the 6.0 together in the camaro and get it ready for the 35psi it will be seeing from the good ole Vortech YSI...

Thanks man. Its coming slowly and taking lots and lots of money ha. My long term plan includes a YSI. Those things are nasty.

what size rr you use?

1.7 Cranes

Did you find that wrench you were looking for?:biggrin:

Ha actually whenever we went over to walmart for the RTV, there was a 7 dollar pipe wrench so we bought that and it actually did the job.

[cwh19]

OK guys two questions.

1. Since I deleted my power steering, I need a new coil mount location. I was thinking about grinding the welded on nuts off of the stock mount, because the holes on the actual bracket are larger than the welded on nuts, and taking one of the bolts from the power steering bracket, putting it through the coil bracket, then some spacers, then mounting it on the head where the steering bracket went. Any ideas on this?


2. The adjustable FPR on my fuel rails is hitting the intake spacer. They are angled in much more than they were on the stock lower. If I just get 1 or 2 washers and put them inbetween the fuel rail mount and the lower to push it away will that be ok?

[1Badbird]

Cars looking great man!

[cwh19]

Got ALOT done today. I'm almost done. Got the hot side piping ran, but not fitted permenately yet. Still have to make the cold side up and then I'll tighten everything down real good. I sent the BOV to Tial today to get the spring switched out so I hope that turn around is quick. Not too much left to do. I had a few vacuum questions but thanks to Tim they are all figured out.



http://i938.photobucket.com/albums/ad230/cwh19/Project/1.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/2.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/3.jpg

http://i938.photobucket.com/albums/ad230/cwh19/Project/4.jpg

[cwh19]

Is this cable for cruise control??





http://i938.photobucket.com/albums/ad230/cwh19/Project/5.jpg

[95riosnake]

Is this cable for cruise control??





http://i938.photobucket.com/albums/ad230/cwh19/Project/5.jpg

Throttle linkage.

That piping setup looks sick, it's nice to see something different. What hood are you going to run to clear that?

[94svtcobra]

What hood are you going to run to clear that?


none exists

[cwh19]

Throttle linkage.

That piping setup looks sick, it's nice to see something different. What hood are you going to run to clear that?

Any idea how it attaches to a fox throttle bracket? I cannot figure it out at all. It seems rather stupid but I can't figure it out.

The straight pipe going down the front needs cut more. From the picture you can tell its actually pushing the top pipe up. We were just tired so we left for the night but its going to get about 2 inches cut off which will lower the top pipe down. I have a 3'' wide cowl in the mail though.

[95riosnake]

Any idea how it attaches to a fox throttle bracket? I cannot figure it out at all. It seems rather stupid but I can't figure it out.

The straight pipe going down the front needs cut more. From the picture you can tell its actually pushing the top pipe up. We were just tired so we left for the night but its going to get about 2 inches cut off which will lower the top pipe down. I have a 3'' wide cowl in the mail though.

I'm not sure, but Tim can probably answer that question or anyone who has converted to a fox style TB. I am still running a 94-95 style TB for now, I may do the conversion someday but I don't want to have to ditch my Anderson NA power pipe and buy one for a fox just to do it.

[scott5]

Any idea how it attaches to a fox throttle bracket? I cannot figure it out at all. It seems rather stupid but I can't figure it out.

The straight pipe going down the front needs cut more. From the picture you can tell its actually pushing the top pipe up. We were just tired so we left for the night but its going to get about 2 inches cut off which will lower the top pipe down. I have a 3'' wide cowl in the mail though.

only 3in wide? you might need a wider one than that.. hahaha..

you need the fox cable to make it work.. the sn95 is too long

[cwh19]

only 3in wide? you might need a wider one than that.. hahaha..

you need the fox cable to make it work.. the sn95 is too long

Lol wide as in the style of the hood is a wide cowl. Not a step up like a cobra hood.

I have the fox throttle cable and the fox bracket. I popped the old cable out, attached the fox cable to the pedal and have it all ready to go. What does this cable do because its obviously not attached to the pedal.

[cwh19]

It ran today! After alot of cranking it finally turned over. I had to pump the gas for a little but after about 30 seconds it idled nice around 900 rpm. It idled for about 10 minutes or so. The fuel pressure, oil pressure, and vacuum all seemed pretty good. I turned it off because my aftermarket temperature gauge wasnt moving but I think I might have forgotten to hook it back up. Open headers are LOUD!

Just some small things left to do and then its off to Tims for the side exhuast, valve body, and tune.

[95riosnake]

It ran today! After alot of cranking it finally turned over. I had to pump the gas for a little but after about 30 seconds it idled nice around 900 rpm. It idled for about 10 minutes or so. The fuel pressure, oil pressure, and vacuum all seemed pretty good. I turned it off because my aftermarket temperature gauge wasnt moving but I think I might have forgotten to hook it back up. Open headers are LOUD!

Just some small things left to do and then its off to Tims for the side exhuast, valve body, and tune.

What setup are you going with for the side exhaust? It seems like I created a side exhaust market for Tim when I had him fab mine a few years ago lol

[94svtcobra]

yep, lol

[cwh19]

What setup are you going with for the side exhaust? It seems like I created a side exhaust market for Tim when I had him fab mine a few years ago lol

Lol yep. Im getting mine done exactly like yours and Mikes. I've seen under Mikes car in person and while I was at Tims one time we looked at pictures of yours. I'm doing longtubes with an x then into SLPs then out the sides. Im just going to have rectangle tips right infront of the tire though. No side exhuast skirts.

I think tail pipes on 94-98s look awkward.

[police4.6]

tell them the news colton.

[cwh19]

My hood came today, along with the T-clamps I had to order. All I'm waiting for now is the blowoff to come back from Tial. That will hopefully be tomorrow.

Does anyone here know the bolt sizes and thread pattern for the fox IAC and TPS sensors? I cannot figure them out at all. I'm sure the car will run better with those two things attached ha.

[Rodeheavers]

the iac should be an 8mmX1.00, or about the same size as a fender bolt..lol your best guess on the tps..

[scott5]

i had dumps on my red car and actually tim has heard and seen that car alot haha.. dunno if it still has dumps on it, but it sounded awesome.. and have been told numerous times that it was the best mustang they heard..

But glad your almost done.. Congrats

[cwh19]

Its almost done. Just need to get a shorter crank belt and put on the tps sensor. I bought a generic male/female harness and I'm going to splice the wires together. Then its off to get the side exhuast put on, a manual valvebody put on and tuned.



Its open headers right now so you can't even hear the blower or BOV.



A shot of the before and then the now.







http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0056.jpg



http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0174.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0175.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0176.jpg


http://i938.photobucket.com/albums/ad230/cwh19/Project/100_0179.jpg

[89 vert]

Looks sweet, nice to see something different!

[police4.6]

haha i think for two @$$ holes not really knowing what to do we did a dam fine job

[1Badbird]

Nice work guys, it looks good!

[06zx3]

looks good man!

[cwh19]

Heres a video.

YouTube- MyCar.MOV

[94svtcobra]

weak sauce, lolz

[Rodeheavers]

oh no.... its alive!!!

[1Badbird]

Sounds good man!

[cwh19]

Thanks guys

[police4.6]

i love how it sets the green car's arming system off.. hahaha

[crazylou]

looks and sounds good...

[94svtcobra]

Colton, I am counting down the days until our cars are tuned, and A my car puts down high hp&tq numbers, n B then i beat you

[MBH]

YouTube- CWH19's H/C and supercharged 5.0

:yo:

[cwh19]

Awesome man thank you.

[94svtcobra]

bo can I reserve you services for the next dyno day?

[95riosnake]

bo can I reserve you services for the next dyno day?

+1 I need some good footage of mine as well

[Balaska347]

Looks and sounds great

[Rodeheavers]

check out big pimping Mike up in there!!!

[Pop's Stang]

That's is awesome!!! Congrat's!!:thumb:

[scott5]

thought it was an h/c/i car?

[94svtcobra]

cleaned up gt40's cobra intake, e cam

[Balaska347]

check out big pimping Mike up in there!!!

lol Im always on I just dont post too much.

[94svtcobra]

check out big pimping Mike up in there!!!

na balaska, he was referring to me sitting shotty, hahaha

[police4.6]

na balaska, he was referring to me sitting shotty, hahaha

yeah before i got to ride in it... haha :smokin: